GE Washer Repair Miami — GTW, GFW, Profile

4.79★ · $59 service call · same day

Same-day slots most days, 7 AM–9 PM. 19 factory-trained technicians, 4.79★ across 1,300 customer reviews — the $59 service call is waived when you proceed with the repair. $59 covers the visit and diagnosis and is credited to the repair if you go ahead. If you don't, it's the only charge.

Request service

Rather not call? Leave your number

Name, phone and what broke. Dispatch calls you back, usually within 10 minutes between 7 AM and 9 PM.

Text us a photoSend a photo of the problem and the model tag to (786) 435-0511, or call (754) 345-4515.

By submitting you agree to be contacted by phone or SMS about your service request. No marketing messages.

GE washer repair across Miami-Dade, Broward and Palm Beach. GTW top-load, GFW front-load, UltraFresh, Profile and the stacked GUD laundry centers. Will not spin, will not drain, lid lock, mode shifter, suspension rods, leaks. $59 service call, free with the repair · 4.79★ · same-day slots most days.

(754) 345-4515 — Dispatch
Request service

GE washers are simpler inside than an LG or a Samsung, and that is their strength. A GTW top-loader has a motor, a mode shifter, a lid lock, a pump and four suspension rods, and when it stops working it is one of those five. The front-load GFW line is newer and closer to the competition in design, with the UltraFresh vent system that finally solved the mildew smell most front-loaders develop in Miami humidity. Since Haier took over GE Appliances in 2016 the parts pipeline has stayed reliable and the prices moderate, which is why a GE washer is usually worth repairing well past the age where we would quote a replacement for other brands.

GE washer models we repair

Top-load GTW335, GTW465, GTW485, GTW500, GTW540, GTW585, GTW680, GTW720, GTW840
Profile top-load PTW600, PTW700, PTW900 with SmartDispense
Front-load GFW450, GFW550, GFW650, GFW850 UltraFresh, Profile PFW870, PFW950
Stacked laundry centers GUD24, GUD27 and the 2-in-1 combo units
Compact 24-inch GFW148 and the older WCVH front-loaders
Older Hydrowave top-loaders (GTWN, GHWN) with the infusor agitator

GE washer problems and what we do about them

Top-loader fills and agitates but will not spin

The lid lock or the mode shifter. GE’s mode shifter sits under the tub and moves the drive between agitate and spin; when its small motor or its position sensor fails, the machine agitates and then sits there. Both are same-visit parts on GTW machines. On the older Hydrowave models the same symptom is the motor inverter board.

Walks, bangs or stops with an unbalance error on spin

Four suspension rods hold the tub on every GE top-loader, and they sag after five or six years. We replace all four together. One new rod and three old ones puts the tub off-center and the code returns in a month.

Will not drain, clothes soaking wet

The drain pump. GE pumps clog with the same coins and socks as any other brand, and the impeller cracks when something hard gets past the inlet. On GFW front-loaders the pump is behind the lower front panel; on GTW top-loaders it is reached from the back. Same-visit part either way.

Front-loader shakes on spin, roars, water underneath

Shock absorbers if it is a shake, drum bearing and seal if it is a roar with water. The GFW bearing lasts longer than most because the UltraFresh line runs a slower final spin, but it is not immortal. We tell you which one it is before quoting.

Fills slowly, or will not stop filling

Inlet valve screens packed with mineral grit from South Florida water, or a failed valve. Overfilling on a GTW is the water level sensor or a pinched pressure hose. Screens are cleaned free with the visit.

Lid will not lock, cycle will not start

The lid lock assembly, or on some GTW models a lid strike that has worn down. A lid that will not lock also blocks the spin, so the two arrive together. A $150 to $280 repair on every current model.

Dead panel, or lights on but nothing happens

The main control board, or a failed motor inverter on the older Hydrowave platform. We check the incoming power, the lid lock circuit and the motor before condemning a board, because a lock that has failed open makes the board look dead.

Leaking from the bottom

A split pump housing, a loose hose clamp, or on top-loaders the tub seal at the base of the drive. Front-loaders leak at the door boot. We find the source with the panel off and water running.

GE washer repair pricing

Job	Typical range*
Service call (applied to the repair)	$59
Lid lock assembly	$150 to $280
Mode shifter (GTW)	$170 to $300
Drain pump	$170 to $300
Suspension rods, set of four	$190 to $330
Inlet valve or water level sensor	$150 to $270
Shock absorbers, pair (GFW)	$210 to $360
Motor inverter board (Hydrowave)	$220 to $400
Main control board	$240 to $440
Door boot gasket (GFW)	$220 to $380
Drum bearing and seal (GFW)	$400 to $640

*Parts and labor, residential. Written quote after the diagnosis; the $59 service call is free with any repair you approve. 90-day labor warranty.

Repair or replace

Almost everything on a GE top-loader is worth repairing at any age under fifteen years, because the parts are inexpensive and the platform has no single failure that takes the whole machine with it. On the front-loaders the line is a drum bearing past eight years, where the repair reaches half the price of a new GFW550. Stacked GUD laundry centers tip toward repair, since replacing one means replacing the dryer too.

Frequently asked questions

Do you repair GE washers in Miami and Fort Lauderdale?

Yes, across Miami-Dade, Broward and Palm Beach, seven days a week. Same-day slots most days when you call before noon at (754) 345-4515. Top-load GTW, front-load GFW, Profile and stacked GUD units.

My GE top-loader agitates but will not spin. What is wrong?

The lid lock or the mode shifter, $150 to $300 either way, repaired the same visit. On older Hydrowave models it can be the motor inverter, $220 to $400.

Why does my GE washer bang and walk on spin?

The four suspension rods have sagged. We replace the set, $190 to $330. Replacing one rod does not work; the tub sits off-center and the noise comes back.

How much does a GE washer drain pump cost?

$170 to $300 with labor, same visit. If the pump only needed clearing, $120 to $180 and the pump stays.

Is a 12-year-old GE washer worth repairing?

A top-loader, usually yes: the parts that fail are cheap and there is no single expensive failure waiting behind them. A front-loader with a drum bearing at twelve years, usually no. We give you both numbers.

Do you service GE Profile and UltraFresh washers?

Yes. Profile PTW and PFW models and the UltraFresh GFW line use the same platforms as the standard GE machines with added dispensers and venting, and we carry the parts.