Skip to main content
Service areas Contact
(754) 345-4515 Call dispatch · 7 AM–9 PM daily

Samsung Dryer Repair

4.79★ · $59 service call · same day

Call (754) 345-4515Request service

Same-day slots most days, 7 AM–9 PM. 19 factory-trained technicians, 4.79★ across 1,300 customer reviews — the $59 service call is waived when you proceed with the repair. $59 covers the visit and diagnosis and is credited to the repair if you go ahead. If you don't, it's the only charge.

Request service
Berne technicians

Rather not call? Leave your number

Name, phone and what broke. Dispatch calls you back, usually within 10 minutes between 7 AM and 9 PM.

Text us a photoSend a photo of the problem and the model tag to (786) 435-0511, or call (754) 345-4515.

By submitting you agree to be contacted by phone or SMS about your service request. No marketing messages.

Samsung dryer repair across Miami-Dade, Broward and Palm Beach. Electric and gas DVE and DVG models, Bespoke, FlexDry, stacked pairs. Not heating, HE, hE, tE and dC codes, heating elements, thermal fuses, idler pulleys, rollers, drum belts. $59 service call, free with the repair · 4.79★ · same-day slots most days.

(754) 345-4515 — Dispatch
Request service

A Samsung dryer that runs but does not heat is the most common dryer call we take in South Florida, and it is one of two parts: the heating element or the thermal fuse that protects it. Both fail for the same reason, a vent that no longer moves air, and a technician who replaces the part without checking the vent will be back in six months. Samsung’s DVE45 and DVE50 electric dryers and the DVG gas versions share a platform, so the parts are on the truck and most calls close in one visit. Here is what fails, what each fix costs, and where the vent fits into the story.

Samsung dryer models we repair

  • Electric DVE45, DVE46, DVE50, DVE52, DVE53, DVE54, DVE60
  • Gas DVG45, DVG50, DVG52, DVG53, DVG54, DVG60
  • Bespoke AI DVE46BB, DVE50BG, DVE53BB
  • FlexDry DVE55, DVE60 two-in-one units
  • Compact 24-inch DV22 ventless and heat pump
  • Stacked pairs with the WF45 and WF50 washers

Samsung dryer codes and symptoms

Runs but no heat, clothes still damp
Electric models: the heating element has opened, or the thermal fuse on the heater housing has blown. Gas models: the igniter, the flame sensor or a gas valve coil. We meter each in order and we check the vent airflow before we leave, because a blown thermal fuse means the dryer overheated, and it overheated because the air was not leaving. Replacing the fuse without the vent is a repeat call.
HE, hE or HC code
Heating fault. On electric units it is the element, the thermistor or the high-limit thermostat; on gas it is the ignition chain. Samsung throws HE when the thermistor sees no temperature rise, so a dryer with a good element and a dead thermistor shows the same code.
Squeal, thump or scrape on every rotation
Drum rollers, the idler pulley or the drum bearing. Samsung idler pulleys start squealing around year five and get loud fast. We replace the rollers as a set with the pulley and the belt while the drum is out, because doing one and leaving three worn ones brings the noise back within a season.
tE, tE3 or tS: thermistor
The temperature sensor in the blower housing has failed or its connector corroded. It is a $30 part and an hour of labor, and it stops a lot of dryers from heating at all.
dC, dE or door open message while closed
Door switch or door latch. On Bespoke units with the reversible door the hinge-side switch is the usual culprit. Same-visit part.
Will not start, hums, or drum does not turn
A snapped drum belt if it hums, a failed drive motor if it does nothing, or a broken belt switch that tells the board the belt is gone. Belts are truck stock.
Takes two cycles, hot to the touch, lint everywhere
The vent. A South Florida condo dryer vent that runs thirty feet through the ceiling clogs with lint and the dryer cannot breathe. We measure the airflow at the outlet, clean the vent to the outside where we can, and tell you when the run itself needs a booster or a rebuild. This is the cause behind most element and fuse failures on this list.
Sensor dry stops early, clothes damp
Moisture sensor bars inside the drum coated with dryer-sheet residue, or a failed sensor harness. Cleaning the bars is included in the visit; a harness is a same-day part.

Samsung dryer repair pricing

Job Typical range*
Service call (applied to the repair) $59
Thermal fuse or high-limit thermostat $130 to $220
Thermistor (tE) $130 to $220
Heating element, electric (HE) $180 to $320
Igniter or flame sensor, gas $170 to $300
Gas valve coils $160 to $280
Door switch or latch (dC) $130 to $230
Drum belt $150 to $250
Rollers, idler pulley and belt, set $240 to $400
Drive motor $280 to $460
Main control board $260 to $440
Dryer vent cleaning to the exterior $140 to $320

*Parts and labor, residential. Written quote after the diagnosis; the $59 service call is free with any repair you approve. 90-day labor warranty. Vent airflow check is included in every heating repair.

Repair or replace

Almost every Samsung dryer repair is worth doing at any age under twelve years, because the parts that fail are cheap and the drum, the cabinet and the motor last. The exception is a drive motor and a control board failing in the same year on a unit past ten years, where the two repairs reach half the price of a new DVE45. Stacked pairs and Bespoke colors tip the math toward repair, since replacing one half rarely matches the other.

Frequently asked questions

Do you repair Samsung dryers in Miami and Broward?
Yes, across Miami-Dade, Broward and Palm Beach, seven days a week, electric and gas. Same-day slots most days when you call before noon at (754) 345-4515. Stacked pairs are unstacked and restacked in the same visit.
Why does my Samsung dryer run but not heat?
On electric models the heating element or the thermal fuse, $130 to $320; on gas the igniter, flame sensor or valve coils, $160 to $300. Either way the vent is checked, because a blocked vent is what killed the part.
What does the HE code mean on a Samsung dryer?
A heating fault: the thermistor saw no temperature rise. It can be the element, the thermistor itself or the high-limit thermostat, and we meter each before replacing anything.
My Samsung dryer squeals on every turn. What is that?
The idler pulley or the drum rollers. We replace the rollers, pulley and belt as a set with the drum out, $240 to $400, so the noise does not come back from the part we left.
How much does it cost to fix a Samsung dryer that will not heat?
$130 to $220 for a thermal fuse or thermistor, $180 to $320 for a heating element, parts and labor, same visit. If the vent needs cleaning to stop it recurring, $140 to $320 more.
Does a blocked dryer vent really break the dryer?
Yes. When air cannot leave, the heater housing overheats and the thermal fuse blows to prevent a fire. Replace the fuse without clearing the vent and it blows again. That is why the airflow check is part of every heating repair we do.

Related: dryer repair, Samsung appliance repair, Samsung washer repair, LG dryer repair, washer repair.

Request service

By submitting you agree to be contacted by phone or SMS about your service request. No marketing messages.

Recent work from our technicians

Finished, paid jobs from our records. Photos are from the visit; client details are left out.

See all dryer jobs →

Call (754) 345-4515