Ice maker repair in Coral Gables
No ice in a Miami summer gets noticed fast. We repair in-refrigerator ice makers, undercounter cube machines and built-in clear-ice units — Sub-Zero to Samsung — with complete assemblies and inlet valves on the truck. $59 service call — free with repair, same-day across South Florida.
Coral Gables, Miami-Dade County • Local ice maker service
What ice maker repair looks like in Coral Gables
Coral Gables is dense with high-end built-in kitchens, so a large share of Gables calls are Sub-Zero, Wolf, Miele and Thermador units where factory-correct parts and sealed-system work matter more than speed.
Because Coral Gables sits on the coast, the salt air and humidity here are hard on ice maker components — we factor that in on every diagnosis and carry coastal-grade parts on the truck.
Common ice maker problems we see in Coral Gables — symptom, cause & typical cost
| Symptom | Most likely cause | Typical repair cost* |
|---|---|---|
| Not cooling, freezer fine | Failed evaporator fan motor or defrost control | $180–$340 |
| Whole unit warm, lights on | Bad start relay, compressor, or sealed-system leak | $250–$650 |
| Leaking water on the floor | Clogged or frozen defrost drain line | $140–$260 |
| Frost build-up in freezer | Defrost heater, thermostat, or door-seal leak | $170–$330 |
| Ice maker not making ice | Water inlet valve, ice-maker module, or frozen fill tube | $160–$340 |
| Loud or constant running | Dirty condenser coils or failing condenser fan | $130–$280 |
*Typical parts-and-labor ranges for Coral Gables-area homes; exact pricing is confirmed on site. The $59 diagnostic fee is waived when you approve the repair. Built-in and luxury brands (Sub-Zero, Viking, Thermador, GE Monogram) can run higher due to sealed-system and factory-part requirements.
Do you offer same-day ice maker repair in Coral Gables?
Yes. Berne Appliance Repair runs same-day ice maker service across Coral Gables, including Miracle Mile, Coral Way, Granada, Riviera. Book before midday and we can usually have a technician at your door the same afternoon. The $59 diagnostic fee is waived when you proceed with the repair.
Which ZIP codes around Coral Gables do you cover?
We routinely handle ice maker repair in ZIP codes 33134, 33143, 33146, 33156, plus the surrounding Miami-Dade area. If your ZIP is not listed, call us — our coverage is wider than the codes shown here.
ice maker repair near Coral Gables
We also serve Coconut Grove, Brickell and the rest of Miami-Dade County.
Ice maker problems we fix every week
No Ice At All
A closed or failed water-inlet valve, a frozen fill tube, a clogged filter, or a dead ice-maker module. All four show up on one $59 diagnostic, and complete assemblies for Samsung, LG, Whirlpool, GE and KitchenAid are stock items on the truck — most no-ice calls finish the first visit.
Small, Cloudy or Hollow Cubes
A water-supply symptom, not a dead machine: a tired filter, a half-failed inlet valve, or South Florida mineral scale on the evaporator plate restricting flow. A descale plus a filter change usually brings back full, clear cubes the same visit.
Ice Tastes or Smells Off
An aged inline filter, a slimed supply line, or stale ice absorbing freezer odors. We replace the filter, sanitize the fill path and bin, and tell you the honest filter-change interval for Hialeah-to-Boca water — usually twice the bag-label schedule.
Leaking Water
A cracked or misaligned fill tube, an inlet valve that no longer shuts fully, or a kinked drain line on undercounter machines. Leak calls get same-day priority for floor-damage risk — shut the supply valve behind the unit if you can reach it and call.
Clear-Ice Machine Stopped Harvesting
On Sub-Zero, KitchenAid, GE Monogram and U-Line clear-ice machines a stuck harvest is usually scale on the evaporator plate or a failed water pump — the unit reads as dead when it needs a descale. Senior refrigeration technicians handle these units.
Sub-Zero ice systems and Gables water
Coral Gables kitchens are built around integrated refrigeration, and a big share of our ice calls here are Sub-Zero columns and built-ins where the ice maker is a serviceable system of its own — dedicated fill valve, mold assembly, control module. These machines reward factory-correct parts and patience; a generic valve with the wrong flow rate will make bad ice in a very good refrigerator, so we fit the right component the first time.
Gables owners keep good machines for decades, and the water turns that into a maintenance relationship: Miami-Dade water leaves scale on the mold and thermostat that slowly distorts harvest timing, so cubes shrink and cloud years before anything truly fails. A periodic descale keeps a twenty-year-old Sub-Zero making ice like new.
In the Mediterranean houses off Coral Way we also check the supply line itself, because original plumbing sheds sediment that clogs inlet screens. And in the bigger properties we service the undercounter bar machines — KitchenAid and U-Line mostly — whose real enemy is a millwork alcove that gives the condenser no air.
How an ice maker repair visit works
1. Tell Us the Machine
In-fridge ice maker, undercounter cube machine, or built-in clear-ice unit — plus the brand and what stopped. That determines which assemblies and valves ride out on the truck.
2. Same-Day Window
Call (754) 345-4515 before noon and dispatch usually books a same-day slot across Miami-Dade, Broward and Palm Beach. Restaurant or bar machine? Say so — commercial routes through Berne Commercial the same day.
3. $59 Diagnostic, In Writing
We test the inlet valve, fill path, filter and module, check for scale on the plate, and hand you a written quote. The $59 service call is free with any repair you approve.
4. Repair From Truck Stock
Complete ice-maker assemblies, inlet valves and filters for the volume brands are on the truck; Sub-Zero and Scotsman residential parts typically arrive in 1–3 business days.
5. First Bucket Verified, Tiered Warranty
We run the unit through a full harvest cycle before closeout and back the repair with a tiered parts warranty — up to 10 years on sealed-system welds — plus a 90-day labor warranty.
Need appointment?
Comments from our customers
